Japanese GENNO HAKKAKU Osho Hammer with an octogonal head. One side of the head is flat, used for example with chisels and hand planes. The other side is slightly convex and used for pushing nails in. Head's weight : 375 grams Total weight (head + handle) : 480grams Total length : 33cm (13") Size of the head : 23x27x88mm T

Japanese GENNO HAKKAKU Osho Hammer with an octogonal head.

One side of the head is flat, used for example with chisels and hand planes. The other side is slightly convex and used for pushing nails into the wood.  

Total length : 33 cm (13)
Size of the head : 23 mm x 27 mm x 88 mm
Head's weight : 375 grams
Total weight (head + handle) : 480 grams

The head is made of hardened steel.
The handle is made by Oak.

Made in Japan.

Small japanese Kebiki marking gauge with 2 adjustable single-bevel marking blades. They leave a very fine and tear-out-free mark without tearing the grain. The advantage of the blade is that it cuts the fibres, whereas a needle tears them. 

It can be used to cut a single line or both blades can be used in tandem to lay out a mortise or tenon.

Size : 120 mm x 120 mm x 70 mm (4.7 x 4.7 x 2.7)
Weight : 165 grams

Made of Oak and carbon steel.

Made in Japan.

Japanese KAKURI brass bar clamps for fine and precise clamping, fitting and glueing small scale work. 

150 mm :
Bar dimension : 150 mm x 4 mm x 4 mm
Clamping width : 125 mm
Clamping depth : 13 mm
Weight : 46g

180 mm :
Bar dimension : 180 mm x 4 mm x 4 mm
Clamping width : 155 mm
Clamping depth : 13 mm
Weight : 50g

240 mm :
Bar dimension : 240 mm x 5 mm x 5 mm
Clamping width : 215 mm
Clamping depth : 14 mm
Weight : 90g

300 mm :
Bar dimension : 300 mm x 5 mm x 5 mm
Clamping width : 275 mm
Clamping depth : 14 mm
Weight : 105g

Kataba saw HSG-10 guide with pre-set angles every 15 degrees :

15-30-45-60-75-90-105-120-135-150-165-180 degrees.

The guide has 2 magnets to guide your saw for an easier cutting control.

Made by ABS.

Weight : about 200 grams

(The saw on the pictures is not included, but is available in my store)

Small japanese Fujiwara Kebiki with 2 adjustable single-bevel marking blades. They leave a very fine and tear-out-free mark without tearing the grain. 

It can be used to cut a single line or both blades can be used in tandem to lay out a mortise or tenon.

Size : 110 mm x 120 mm x 70 mm (4.3 x 4.7 x 2.7)
Weight : 165 grams

Made in Japan.

Japanese MOKUBA C-6 cat's paw 200 mm (7.9) 3 ways claw bar.

Weight : 180 grams
Total length : 200 mm (7.9)
Widest part : 43 mm (1.7)

The back of the head also functions as a small tack hammer to easily grab the nails. It is the ideal tool for taking apart assembled pieces of furniture. Wide and slender with a beveled edge allowing the claw to easily fit into joints, and it is curved to maximize its leverage capability.

The bar is made of forged hardened steel. 

Made in Japan.

Japanese Z-saw Zetsaw cutting guide for Kataba saw (blade thickness between 0,4 mm and 0,6 mm) + 1 saw 265 mm and 1 protractor included.

You will be able to cut precision 90 degrees square cuts and miter cuts at any angle up to 45 degrees in both left and right directions as 45 degrees slopes in both directions.
Long straight cuts are also possible by attaching the included sliding fence.
The tool you need to make straight and accurate cuts at the right angle with your kataba saw.

Body : Galvanized steel
Weight of the box : 1550 grams

Made in Japan.

Japanese MOKUBA C-7 cat's paw 360 mm (14.2) claw bar

Weight : 700 grams
Total length : 360 mm (14.2)

The back of the head also functions as a small tack hammer to easily grab the nails.

The bar is made of forged hardened steel.

Made in Japan.

Japanese YAMAZAKI Carbon steel bar clamp for fine and precise clamping, fitting and glueing small and medium scale work. 
6 holes are drilled into the back of the bar allowing the clamp to be used at a higher pressure without worrying that the arm might slide. 

360 mm :
Bar dimension : 400 mm x 7 mm x 7 mm
Clamping width : 360 mm
Clamping depth : 26 mm
Weight : 305 g

Made in Japan.

Shinwa 78217 circular saw guide 300 mm

The tool you need to make straight cuts at the right angle with your circular saw.

With quick adjustment mechanism to set up 45 degrees, 90 degrees and 135 degrees.

You can use it in the reverse way (see pictures)

Size : 439 mm x 100 mm x 26 mm
Weight : about 500 grams
Made of stainless steel, aluminum, brass, ABS, POM

Made in Japan.

Shinwa 78176 circular saw and jigsaw guide 230 mm.

The tool you need to make straight cuts at the right angle with your circular saw.

With a flat screw to secure the angle, so that your saw can easily pass over the guide.

You can use it in the reverse way (see pictures)

Size : 350 mm x 105 mm x 26 mm
Weight : about 400 grams
Made of stainless steel, brass

Made in Japan.

Japanese GENNO FUNATE nailing precision hammer.

One side of the head has an octogonal shape with a slightly domed face and the other side has a 4x5mm rectangular shape for high precision work.

Total length : 36 cm (14.2)
Size of the head : 29 mm x 29 mm x 128 mm
Head's weight : 360 grams
Total weight (head + handle) : 490 grams

The head is made of hardened steel.
The handle is made by Oak.

Made in Japan.

KTC Kyototool UDP-4 Auto punch.

Single-handed punching without using a hammer. Works with materials like wood, plastic, metal, glass, and leather.

Automatic center punches are important when it comes to marking an accurate drilling location. This one-hand-held puncher lets you mark drill holes anywhere while on the job, great to improve your productivity.

You can set the strength of the impact by turning the top part of the handle. 

Size : 160 mm long (6.3) and 35 mm wide (1.4)
Weight : 165 grams

Made in Japan.

Precision Z saw guide saw 265mm with slopes 45 90 degrees Japan Zetsaw - Osaka Tools

Z-saw Zetsaw Zsaw guide 45-90 degrees + 2 saws 265mm + 180mm Japan - Osaka Tools

KAKURI Hatagane Brass bar clamps clamp made in Japan - Osaka Tools

Japanese MOKUBA C-6 200mm Pry nail puller claw bar Made in Japan - Osaka Tools

Scie Japonaise pliable pliante PRO-ACT bois 210mm + lame supplementaire JAPON

Japanese Hammer GENNO HAKKAKU Osho octogonal 375g Japan - Osaka Tools

YAMAZAKI Hatagane Steel bar clamps clamp made in Japan - Osaka Tools

Japanese Z-saw Zsaw saw KATABA HI III 265mm 10.4 cross diagonal rip cut Japan

YAMAZAKI Hatagane Steel bar clamps clamp made in Japan - Osaka Tools

Japanese KTC Auto automatic punch UDP-4 UDP-4-1 Kyototool Japan - Osaka Tools

Osho Daruma Genno Hammer 375g – Urban Toolworks

Japanese Hammer GENNO HAKKAKU Osho octogonal 375g Japan - Osaka Tools

Japanese MOKUBA C-7 360mm Pry nail puller cat's paw Made in Japan - Osaka Tools